Technická data
Název:
SIPLUS PS PSE200U 10A
Popis:
SIPLUS PS PSE200U 10A WITH CONFORMAL COATING BASED ON 6EP1961-2BA41 . SELECTIVITY MODULE 4 CHANNELS INPUT: 24 V DC OUTPUT: 24V DC/10 A PER CHANNEL OUTPUT CURRENT ADJUSTABLE 3-10 WITH STATUS MESSAGE PER CHANNEL
Technické informace:
SIPLUS PS PSE200U 10A WITH CONFORMAL COATING BASED ON 6EP1961-2BA41 . SELECTIVITY MODULE 4 CHANNELS INPUT: 24 V DC OUTPUT: 24V DC/10 A PER CHANNEL OUTPUT CURRENT ADJUSTABLE 3-10 WITH STATUS MESSAGE PER CHANNEL | ||
Input | ||
Type of the power supply network | Controlled DC voltage | |
Supply voltage / at DC / Rated value | 24 V | |
Input voltage / at DC | 22 ... 30 V | |
Overvoltage overload capability | 35 V | |
Input current / at rated input voltage 24 V / Rated value | 40 A | |
Output | ||
Voltage curve / at output | controlled DC voltage | |
Formula for output voltage | Vin - approx. 0.2 V | |
Relative overall tolerance / of the voltage / Note | In accordance with the supplying input voltage | |
Number of outputs | 4 | |
Output current / up to 60 °C / per output / rated value | 10 A | |
Adjustable pick-up value current / of the current-dependent overload release | 3 ... 10 A | |
Type of response value setting | via potentiometer | |
Product feature / parallel switching of outputs | No | |
Product feature / bridging of equipments | Yes | |
Type of outputs connection | Simultaneous connection of all outputs after power up of the supply voltage > 20 V, delay time of 25 ms, 100 ms or adjustable "load optimised" via DIP switch for sequential connection | |
Efficiency | ||
Efficiency in percent | 99 % | |
Power loss [W] / at rated output current / at rated output current / typical | 10 W | |
Switch-off characteristic per output | ||
Switching characteristic | ||
● of the excess current | Iout = 1.0 ...1.5 x set value, switch-off after approx. 5 s | |
● of the current limitation | Iout = 1.5 x set value, switch-off after typ. 100 ms | |
● of the immediate switch-off | Iout > set value and Vin < 20 V, switch-off after approx. 0.5 ms | |
Design of the reset device/resetting mechanism | via sensor per output | |
Remote reset function | Non-electrically isolated 24 V input (signal level "high" at > 15 V) | |
Protection and monitoring | ||
Overload protection type / for cables | 15 A per output (not accessible) | |
Display version / for normal operation | Three-color LED per output: green LED for "Output switched through"; yellow LED for "Output switched off manually"; red LED for "Output switched off due to overcurrent" | |
Design of the switching contact / for signaling function | Status signal output (pulse/pause signal, can be evaluated via Simatic function block) | |
Safety | ||
Galvanic isolation / between input and output at switch-off | No | |
Operating resource protection class | Class III | |
Certificate of suitability | ||
● CE marking | Yes | |
Standard / for safety | according to EN 60950-1 and EN 50178 | |
Shipbuilding approval | GL, ABS | |
Protection class IP | IP20 | |
EMC | ||
Standard | ||
● for emitted interference | EN 55022 Class B | |
● for interference immunity | EN 61000-6-2 | |
Operating data | ||
Ambient temperature | ||
● during operation | -25 ... +70 °C | |
— Note | with natural convection | |
● during transport | -40 ... +85 °C | |
● during storage | -40 ... +85 °C | |
Environmental category / acc. to IEC 60721 | 3B2, 3C4, 3S4 | |
Ambient condition / relating to ambient temperature - air pressure - installation altitude | Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) | |
Coating | Conformal Coating | |
Relative humidity / with condensation / maximum | 200 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions) | |
Resistance to biologically active substances / conformity acc. to EN 60721-3-3 | Yes; Compliant with EN 60721-3-3, Class 3B2 mold and fungal spores (except fauna); the supplied plug covers must remain in place on the unused interfaces during operation. | |
Resistance to chemically active substances / conformity acc. to EN 60721-3-3 | Yes | |
Resistance to mechanically active substances / conformity acc. to EN 60721-3-3 | Yes; Conformity with EN 60721-3-3, Class 3S4 incl. Sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
Mechanics | ||
Type of electrical connection | screw-type terminals | |
● at input | +24 V: 2 screw terminals for 0.5 ... 10 mm²; 0 V: 2 screw terminals for 0.5 ... 4 mm² | |
● at output | Output 1 ... 4: 1 screw terminal each for 0.5 ... 4 mm² | |
● for signaling contact | 1 screw terminal for 0.5 ... 4 mm² | |
● for auxiliary contacts | Remote reset: 1 screw terminal for 0.5 ... 4 mm² | |
Width / of the enclosure | 72 mm | |
Height / of the enclosure | 80 mm | |
Depth / of the enclosure | 72 mm | |
Installation width | 72 mm | |
Mounting height | 180 mm | |
Net weight | 0.2 kg | |
Mounting type | Snaps onto DIN rail EN 60715 35x7.5/15 | |
Mechanical accessories | Device identification label 20 mm × 7 mm, pale turquoise 3RT1900-1SB20 | |
Other information | Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) |