Technická data
Název:
SIPLUS PS DC-USV 24V/15A
Popis:
SIPLUS PS DC-USV 24V/15A -25 ... + 60 DEGREES C BASED ON 6EP1931-2EC21
Technické informace:
SIPLUS PS DC-USV 24V/15A -25 ... + 60 DEGREES C BASED ON 6EP1931-2EC21 | ||
Input | ||
Supply voltage at DC Rated value | 24 V | |
Voltage curve at input | DC | |
input voltage range | 22 ... 29 V DC | |
Adjustable response value voltage for buffer connection preset | 22.5 V | |
Adjustable response value voltage for buffer connection | 22 ... 25.5 V; Adjustable in 0.5 V increments | |
Input current at rated input voltage 24 V Rated value | 15 A; + approx. 1 A with empty battery | |
Mains buffering | ||
Type of energy storage | with batteries | |
Design of the mains power cut bridging-connection | Dependent on connected battery and load current, see selection table battery module and mains buffering times as well as the relevant important information notes! | |
Charging current | ||
● 1 | 0.35 A | |
● 2 | 0.7 A | |
adjustable charging current maximum Note | factory setting approx. 0.7 A | |
Output | ||
Output voltage | ||
● in normal operation at DC Rated value | 24 V | |
● in buffering mode at DC Rated value | 24 V | |
Formula for output voltage | Vin - approx. 0.5 V | |
ON-delay time typical | 1 s | |
Voltage increase time of the output voltage typical | 60 ms | |
Output voltage in buffering mode at DC | 19 ... 28.5 V | |
Output current | ||
● Rated value | 15 A | |
● in normal operation | 0 ... 15 A | |
● in buffering mode | 0 ... 15 A | |
Peak current | 15.7 A | |
Property of the output Short-circuit proof | Yes | |
Supplied active power typical | 360 W | |
Efficiency | ||
Efficiency in percent | ||
● at rated output current at rated output current typical | 96.2 % | |
● in case of accumulator operation typical | 96 % | |
Power loss [W] | ||
● at rated output current at rated output current typical | 14 W | |
● in case of accumulator operation typical | 15 W | |
Protection and monitoring | ||
Product function | ||
● reverse polarity protection against energy storage unit polarity reversal | Yes | |
● reverse polarity protection against input voltage polarity reversal | Yes | |
Signaling | ||
Display version | ||
● for normal operation | Normal operation: LED green (OK), floating changeover contact "Bat/OK" to setting "OK" ("OK" means: Voltage of the supplying power supply unit is greater than cut-in threshold set at the DC UPS module); Lack of buffer standby: LED red (alarm), floating changeover contact "Alarm/Bat" to setting "Alarm"; Battery replacement required: LED red (alarm) flashing with approx. 0.25 Hz, floating changeover contact "Alarm/Bat" switching with approx. 0.25 Hz; Energy storage > 85%: LED green (Bat > 85%), floating NO contact "Bat > 85" closed; Permissible contact current capacity: DC 60 V/1 A or AC 30 V /1 A | |
● in buffering mode | Buffered mode: LED yellow (Bat), floating changeover contact "OK/Bat" to setting "Bat"; Prewarning battery voltage < 20.4 VDC: LED red (alarm), floating changeover contact "Alarm/Bat" to setting "Alarm"; Energy storage > 85%: LED green (Bat > 85%), floating NO contact "Bat > 85" closed | |
Interface | ||
Product component PC interface | No | |
Design of the interface | without | |
Safety | ||
Galvanic isolation between entrance and outlet | No | |
Operating resource protection class | Class III | |
Certificate of suitability | ||
● CE marking | Yes | |
● as approval for USA | cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259 | |
● relating to ATEX | - | |
● C-Tick | No | |
Shipbuilding approval | GL | |
Protection class IP | IP20 | |
EMC | ||
Standard | ||
● for emitted interference | EN 55022 Class B | |
● for interference immunity | EN 61000-6-2 | |
Operating data | ||
Ambient temperature | ||
● during operation | -25 ... +60 °C; with natural convection | |
● during transport | -40 ... +85 °C | |
● during storage | -40 ... +85 °C | |
Environmental category acc. to IEC 60721 | Climate class 3K6 | |
Relative humidity with condensation maximum | 100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions) | |
Resistance to biologically active substances conformity acc. to EN 60721-3-3 | Yes; Compliant with EN 60721-3-3, Class 3B2 mold and fungal spores (except fauna); the supplied plug covers must remain in place on the unused interfaces during operation. | |
Resistance to chemically active substances conformity acc. to EN 60721-3-3 | Yes; Compliant with EN 60721-3-3, Class 3C4 incl. salt spray in accordance with EN 60068-2-52 (severity 3); the supplied plug covers must remain in place on the unused interfaces during operation. | |
Resistance to mechanically active substances conformity acc. to EN 60721-3-3 | Yes; Conformity with EN 60721-3-3, Class 3S4 incl. Sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
Mechanics | ||
Type of electrical connection | screw-type terminals | |
● at input | 24 V DC: 2 screw terminals for 1 ... 4 mm²/17 ... 11 AWG | |
● at output | 24 V DC: 4 screw terminals for 1 ... 4 mm²/17 ... 11 AWG | |
● for battery module | 24 V DC: 2 screw terminals for 1 ... 4 mm²/17 ... 11 AWG | |
● for control circuit and status message | 10 screw terminals for 0.5 ... 2.5 mm²/20 ... 13 AWG | |
Width of the enclosure | 50 mm | |
Height of the enclosure | 125 mm | |
Depth of the enclosure | 125 mm | |
Required spacing | ||
● top | 50 mm | |
● bottom | 50 mm | |
● left | 0 mm | |
● right | 0 mm | |
Net weight | 0.4 kg | |
Product feature of the enclosure housing for side-by-side mounting | Yes | |
Mounting type | Snaps onto DIN rail EN 60715 35x7.5/15 | |
Electrical accessories | Battery module | |
MTBF at 40 °C | 791 139 h | |
Equipment marking acc. to DIN EN 81346-2 | T | |
Other information | Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) |