Technická data
Název:
SIPLUS PS PSU100M
Popis:
SIPLUS PS MODULAR 40A -40 ... +70 DEGREE C WITH CONFORMAL COATING BASED ON 6EP1337-3BA00 . STABILIZED POWER SUPPLY INPUT: AC 120/230 V OUTPUT: DC 24 V/40 A
Technické informace:
| SIPLUS PS MODULAR 40A -40 ... +70 DEGREE C WITH CONFORMAL COATING BASED ON 6EP1337-3BA00 . STABILIZED POWER SUPPLY INPUT: AC 120/230 V OUTPUT: DC 24 V/40 A | ||
| Input | ||
| Input | 1-phase AC | |
| Supply voltage | ||
| ● 1 at AC Rated value | 120 V | |
| ● 2 at AC Rated value | 230 V | |
| ● Note | Set by means of wire jumper on the device; starting from Vin > 95/190 V | |
| Input voltage | ||
| ● 1 at AC | 85 ... 132 V | |
| ● 2 at AC | 176 ... 264 V | |
| Wide-range input | No | |
| Overvoltage resistance | 2.3 × Vin rated, 1.3 ms | |
| Mains buffering at Iout rated, min. | 20 ms; at Vin = 230 V | |
| Rated line frequency 1 | 50 Hz | |
| Rated line frequency 2 | 60 Hz | |
| Rated line range | 47 ... 63 Hz | |
| Input current | ||
| ● at rated input voltage 120 V | 15 A | |
| ● at rated input voltage 230 V | 8 A | |
| Switch-on current limiting (+25 °C), max. | 125 A | |
| I²t, max. | 26 A²·s | |
| Built-in incoming fuse | Yes | |
| Protection in the mains power input (IEC 898) | Recommended miniature circuit breaker at 1-phase operation: 20 A characteristic C; required at 2-phase operation: circuit breaker 2-pole connected or circuit breaker 3RV2421-4BA10 (120 V) or 3RV2411-1JA10 (230 V) | |
| Output | ||
| Output | Controlled, isolated DC voltage | |
| Rated voltage Vout DC | 24 V | |
| Total tolerance, static ± | 3 % | |
| Static mains compensation, approx. | 0.1 % | |
| Static load balancing, approx. | 0.1 % | |
| Residual ripple peak-peak, max. | 100 mV | |
| Residual ripple peak-peak, typ. | 60 mV | |
| Spikes peak-peak, max. (bandwidth: 20 MHz) | 200 mV | |
| Spikes peak-peak, typ. (bandwidth: 20 MHz) | 120 mV | |
| Adjustment range | 24 ... 28.8 V | |
| Product function Output voltage adjustable | Yes | |
| Output voltage setting | via potentiometer | |
| Status display | Green LED for 24 V OK | |
| Signaling | via signaling module (6EP1961-3BA10) | |
| On/off behavior | Overshoot of Vout approx. 3 % | |
| Startup delay, max. | 0.1 s | |
| Voltage rise, typ. | 50 ms | |
| Rated current value Iout rated | 40 A | |
| Current range | 0 ... 40 A | |
| ● Note | +60 ... +70 °C: Derating 2.5%/K | |
| Supplied active power typical | 960 W | |
| Short-term overload current | ||
| ● at short-circuit during operation typical | 120 A | |
| Duration of overloading capability for excess current | ||
| ● at short-circuit during operation | 25 ms | |
| Constant overload current | ||
| ● on short-circuiting during the start-up typical | 46 A | |
| Parallel switching for enhanced performance | Yes; switchable characteristic | |
| Numbers of parallel switchable units for enhanced performance | 2 | |
| Efficiency | ||
| Efficiency at Vout rated, Iout rated, approx. | 88 % | |
| Power loss at Vout rated, Iout rated, approx. | 131 W | |
| Closed-loop control | ||
| Dynamic mains compensation (Vin rated ±15 %), max. | 1 % | |
| Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. | 2 % | |
| Load step setting time 50 to 100%, typ. | 2 ms | |
| Load step setting time 100 to 50%, typ. | 2 ms | |
| Setting time maximum | 5 ms | |
| Protection and monitoring | ||
| Output overvoltage protection | < 35 V | |
| Current limitation, typ. | 46 A | |
| Property of the output Short-circuit proof | Yes | |
| Short-circuit protection | Alternatively, constant current characteristic approx. 46 A or latching shutdown | |
| Enduring short circuit current RMS value | ||
| ● typical | 46 A | |
| Overload/short-circuit indicator | LED yellow for "overload", LED red for "latching shutdown" | |
| Safety | ||
| Primary/secondary isolation | Yes | |
| Galvanic isolation | Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 | |
| Protection class | Class I | |
| Leakage current | ||
| ● maximum | 3.5 mA | |
| ● typical | 0.4 mA | |
| CE mark | Yes | |
| UL/cUL (CSA) approval | cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259 | |
| Explosion protection | IECEx Ex nA IIC T3 Gc; ATEX (EX) II 3G Ex nA IIC T3 Gc; cCSAus (CSA C22.2 No. 213, ANSI/ISA-12.12.01) Class I, Div. 2, Group ABCD, T3 | |
| FM approval | - | |
| CB approval | No | |
| Marine approval | - | |
| Degree of protection (EN 60529) | IP20 | |
| EMC | ||
| Emitted interference | EN 55022 Class B | |
| Supply harmonics limitation | - | |
| Noise immunity | EN 61000-6-2 | |
| Operating data | ||
| Ambient temperature | ||
| ● during operation | 0 ... 70 °C | |
| — Note | with natural convection | |
| ● during transport | -40 ... +85 °C | |
| ● during storage | -40 ... +85 °C | |
| Humidity class according to EN 60721 | Climate class 3K8H | |
| Relative humidity with condensation maximum | 100 %; Relative humidity, incl. condensation/frost permitted (no commissioning under condensation conditions) | |
| Resistance to biologically active substances conformity acc. to EN 60721-3-3 | Yes; Compliant with EN 60721-3-3, Class 3B2 mold and fungal spores (except fauna); the supplied plug covers must remain in place on the unused interfaces during operation. | |
| Resistance to chemically active substances conformity acc. to EN 60721-3-3 | Yes; Compliant with EN 60721-3-3, Class 3C4 incl. salt spray in accordance with EN 60068-2-52 (severity 3); the supplied plug covers must remain in place on the unused interfaces during operation. | |
| Resistance to mechanically active substances conformity acc. to EN 60721-3-3 | Yes; Conformity with EN 60721-3-3, Class 3S4 incl. Sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
| Mechanics | ||
| Connection technology | screw-type terminals | |
| Connections | ||
| ● Supply input | L, N, PE: 1 screw terminal each for 0.2 ... 4 mm² single-core/finely stranded | |
| ● Output | +, -: 2 screw terminals each for 0.5 ... 10 mm² | |
| Width of the enclosure | 240 mm | |
| Height of the enclosure | 125 mm | |
| Depth of the enclosure | 125 mm | |
| Required spacing | ||
| ● top | 50 mm | |
| ● bottom | 50 mm | |
| ● left | 0 mm | |
| ● right | 0 mm | |
| Weight, approx. | 2.9 kg | |
| Product feature of the enclosure housing for side-by-side mounting | Yes | |
| Installation | Snaps onto DIN rail EN 60715 35x15 | |
| Electrical accessories | Buffer module, signaling module | |
| MTBF at 40 °C | 540 249 h | |
| Other information | Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) | |
