Technická data
Název:
SIPLUS S7-1200 CM 1243-5
Popis:
SIPLUS S7-1200 CM 1243-5; -25 ... +55 DEGREES C WITH CONFORMAL COATING BASED ON 6GK7243-5DX30-0XE0 . COMMUNICATION MODULE CM 1243-5, TO THE CONNECTION OFF S7-1200 TO PROFIBUS AS A DP MASTER ASSEMBLY
Technické informace:
Product type designation | SIPLUS S7-1200 CM 1243-5 | |
Transmission rate | ||
Transfer rate | ||
● at the 1st interface / acc. to PROFIBUS | 9.6 kbit/s ... 12 Mbit/s | |
Interfaces | ||
Number of interfaces / acc. to Industrial Ethernet | 0 | |
Number of electrical connections | ||
● at the 1st interface / acc. to PROFIBUS | 1 | |
● for power supply | 1 | |
Type of electrical connection | ||
● at the 1st interface / acc. to PROFIBUS | 9-pin Sub-D socket (RS485) | |
● for power supply | 3-pole terminal block | |
Supply voltage, current consumption, power loss | ||
Type of voltage / of the supply voltage | DC | |
Supply voltage / external | 24 V | |
Supply voltage / external / at DC / Rated value | 24 V | |
Relative positive tolerance / at DC / at 24 V | 20 % | |
Relative negative tolerance / at DC / at 24 V | 20 % | |
Consumed current | ||
● from external supply voltage / at DC / at 24 V / typical | 0.1 A | |
Power loss [W] | 2.4 W | |
Permitted ambient conditions | ||
Ambient temperature | ||
● during operation | -25 ... +55 °C | |
● for vertical installation / during operation | -25 ... +45 °C | |
● for horizontally arranged busbars / during operation | -25 ... +55 °C | |
● during storage | -40 ... +70 °C | |
● during transport | -40 ... +70 °C | |
Ambient condition / relating to ambient temperature - air pressure - installation altitude | -25 ... +55°C at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // -25 ... +45°C at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // -25 ... +35°C at 658 hPa ... 540 hPa (+3500 m ... +5000 m) | |
Relative humidity / with condensation / maximum | 100 %; r.F., incl. condensation/frost permitted (no commissioning in bedewed state) | |
Resistance to biologically active substances | ||
● conformity acc. to EN 60721-3-3 | Yes; Compliance with EN 60721-3-3, Class 3B2 mold, fungus, and sponge spores (except fauna). The supplied plug covers must remain in place over the unused interfaces during operation! | |
Resistance to chemically active substances | ||
● conformity acc. to EN 60721-3-3 | Yes; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3). The supplied plug covers must remain in place over the unused interfaces during operation! | |
Resistance to mechanically active substances | ||
● conformity acc. to EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied plug covers must remain in place over the unused interfaces during operation! | |
Protection class IP | IP20 | |
Design, dimensions and weight | ||
Module format | Compact module S7-1200 single width | |
Width | 30 mm | |
Height | 100 mm | |
Depth | 75 mm | |
Net weight | 0.134 kg | |
Mounting type | ||
● 35 mm DIN rail mounting | Yes | |
● S7-300 rail mounting | No | |
● wall mounting | Yes | |
Product properties, functions, components / general | ||
Number of units | ||
● per CPU / maximum | 1 | |
Performance data / PROFIBUS DP | ||
Service / as DP master | ||
● DPV1 | Yes | |
Number of DP slaves / on DP master / usable | 16 | |
Amount of data | ||
● of the address area of the inputs / as DP master / total | 512 byte | |
● of the address area of the outputs / as DP master / total | 512 byte | |
● of the address area of the inputs / per DP slave | 244 byte | |
● of the address area of the outputs / per DP slave | 244 byte | |
● of the address area of the diagnostic data / per DP slave | 240 byte | |
Service / as DP slave | ||
● DPV0 | No | |
● DPV1 | No | |
Performance data / S7 communication | ||
Number of possible connections / for S7 communication | ||
● maximum | 8 | |
● with PG connections / maximum | 1 | |
● with PG/OP connections / maximum | 3 | |
● Note | max. 4 connections to other S7 stations | |
Performance data / multi-protocol mode | ||
Number of active connections / with multi-protocol mode | ||
● without DP / maximum | 8 | |
● with DP / maximum | 8 | |
Performance data / telecontrol | ||
Protocol / is supported | ||
● TCP/IP | No | |
Configuration software | ||
● required | STEP 7 Basic/Professional V11 (TIA Portal) or higher | |
Further Information / Internet Links | ||
Internet-Link | ||
● to website: Selector SIMATIC NET SELECTION TOOL | http://www.siemens.com/snst | |
● to website: Industrial communication | http://www.siemens.com/simatic-net | |
● to website: Industry Mall | https://mall.industry.siemens.com | |
● to website: Information and Download Center | http://www.siemens.com/industry/infocenter | |
● to website: Image database | http://automation.siemens.com/bilddb | |
● to website: CAx Download Manager | http://www.siemens.com/cax | |
● to website: Industry Online Support | https://support.industry.siemens.com | |
Security information | ||
Security information | Siemens provides products and solutions with industrial security functions that support the secure operation of plants, solutions, machines, equipment and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens’ products and solutions undergo continuous development. Siemens recommends strongly that you regularly check for product updates. For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action(e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be considered. For more information about industrial security, visit http://www.siemens.com/industrialsecurity. To stay informed about product updates as they occur, sign up for a product-specific newsletter. For more information, visit http://support.automation.siemens.com. (V3.4) | |
last modified: | 01/30/2017 |