Technická data
Název:
SIPLUS ET200S EM F-DI 24V Profisafe
Popis:
SIPLUS ET200S F-DI 24V PROFISAF -25 ... +60 DEGREES C WITH CONFORMAL COATING BASED ON 6ES7138-4FA05-0AB0 . ELECTRON. MODULE F. ET200S, 4/8 F-DI PROFISAFE, 24V DC, 30 MM WIDTH UP TO CATEGORY 4 (EN954-1)/ SIL3 (IEC61508)/PLE (ISO13849), ALSO USEABLE IN PROFINET- NETWORK WITH IM151-3 HF
Technické informace:
Supply voltage | ||
Rated value (DC) | ||
● 24 V DC | Yes | |
permissible range, lower limit (DC) | 20.4 V | |
permissible range, upper limit (DC) | 28.8 V | |
Encoder supply | ||
Number of outputs | 2 | |
Type of output voltage | min. L+ (-1.5 V) | |
Short-circuit protection | Yes; Electronic (response threshold 0.7 A to 1.8 A) | |
Output current | ||
● Rated value | 300 mA | |
● permissible range | 0 to 300 mA | |
Power loss | ||
Power loss, typ. | 4 W | |
Address area | ||
Occupied address area | ||
● Inputs | 6 byte | |
● Outputs | 4 byte | |
Digital inputs | ||
Number of digital inputs | 8; 8 (one-channel); 4 (two-channel) | |
Input characteristic curve in accordance with IEC 61131, type 1 | Yes | |
Number of simultaneously controllable inputs | ||
● Number of simultaneously controllable inputs | 8 | |
Input voltage | ||
● Type of input voltage | DC | |
● Rated value (DC) | 24 V | |
Input current | ||
● for signal "1", typ. | 3.7 mA | |
Input delay (for rated value of input voltage) | ||
for standard inputs | ||
— parameterizable | Yes | |
— at "0" to "1", min. | 0.3 ms | |
— at "0" to "1", max. | 17 ms | |
— at "1" to "0", min. | 0.3 ms | |
— at "1" to "0", max. | 17 ms | |
Cable length | ||
● shielded, max. | 500 m | |
● unshielded, max. | 500 m | |
Encoder | ||
Connectable encoders | ||
● 2-wire sensor | No | |
— permissible quiescent current (2-wire sensor), max. | 0.6 mA; max. | |
Interrupts/diagnostics/status information | ||
Diagnostic functions | Yes | |
Alarms | ||
● Diagnostic alarm | Yes | |
Diagnostic messages | ||
● Diagnostic information readable | Yes | |
● Short-circuit | Yes | |
Diagnostics indication LED | ||
● Group error SF (red) | Yes | |
● Status indicator digital input (green) | Yes | |
Potential separation | ||
Potential separation digital inputs | ||
● between the channels | No | |
● between the channels and backplane bus | Yes | |
● Between the channels and load voltage L+ | No | |
Standards, approvals, certificates | ||
Highest safety class achievable in safety mode | ||
● acc. to EN 954 | 4 | |
● Performance level according to ISO 13849-1 | PLe | |
● SIL acc. to IEC 61508 | SIL 2 (single-channel), SIL 3 (two-channel) | |
Ambient conditions | ||
Ambient temperature during operation | ||
● min. | -25 °C | |
● max. | 60 °C | |
Extended ambient conditions | ||
● relative to ambient temperature-atmospheric pressure-installation altitude | Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) | |
● At cold restart, min. | -25 °C | |
Relative humidity | ||
— With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) | |
Resistance | ||
— against biologically active substances / conformity with EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation! | |
— against chemically active substances / conformity with EN 60721-3-3 | Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! | |
— against mechanically active substances / conformity with EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
Dimensions | ||
Width | 30 mm | |
Height | 81 mm | |
Depth | 52 mm | |
Weights | ||
Weight, approx. | 78 g | |
last modified: | 02/01/2017 |