Technická data
Název:
SIPLUS ET200S EM F-DO 24V Profisafe
Popis:
SIPLUS ET200S F-DO 24V PROFISAF -25 ... +60 GRAD C MIT CONFORMAL COATING BASED ON 6ES7138-4FB04-0AB0 . ELECTRON. MODULE F. ET200S, 4 F-DO PROFISAFE, DC 24V/2A, 30 MM WIDTH UP TO CATEGORY 4 (EN954-1)/ SIL3 (IEC61508)/PLE (ISO13849), ALSO USEABLE IN PROFINET- NETWORKS WITH IM151-3 HF
Technické informace:
| Supply voltage | ||
| Load voltage L+ | ||
| ● Rated value (DC) | 24 V | |
| ● Reverse polarity protection | No | |
| Input current | ||
| From load voltage L+ (no load), typ. | 100 mA | |
| from backplane bus 3.3 V DC, max. | 28 mA | |
| Power loss | ||
| Power loss, typ. | 3.5 W | |
| Digital outputs | ||
| Number of digital outputs | 4 | |
| Short-circuit protection | Yes | |
| Limitation of inductive shutdown voltage to | Typ. (2L+) -47 V | |
| Controlling a digital input | No | |
| Switching capacity of the outputs | ||
| ● on lamp load, max. | 10 W | |
| Load resistance range | ||
| ● lower limit | 12 Ω | |
| ● upper limit | 1 kΩ | |
| Output voltage | ||
| ● for signal "1", min. | L+ (-2,0 V), current sourcing switch: L+ (-1,5 V), voltage drop on current sinking switch: max. 0.5 V | |
| Output current | ||
| ● for signal "1" rated value | 2 A | |
| ● for signal "1" permissible range, min. | 20 mA | |
| ● for signal "1" permissible range, max. | 2.4 A | |
| ● for signal "0" residual current, max. | 0.5 mA; Current-sourcing and current-sinking switches | |
| Parallel switching of two outputs | ||
| ● for uprating | No | |
| ● for redundant control of a load | No | |
| Switching frequency | ||
| ● with resistive load, max. | 30 Hz; Symmetrical | |
| ● with inductive load, max. | 0.1 Hz; Symmetrical | |
| ● on lamp load, max. | 10 Hz; Symmetrical | |
| Total current of the outputs | ||
| ● Current per module, max. | 6 A | |
| Total current of the outputs (per group) | ||
| horizontal installation | ||
| — up to 40 °C, max. | 6 A | |
| — up to 55 °C, max. | 5 A | |
| — up to 60 °C, max. | 4 A | |
| vertical installation | ||
| — up to 40 °C, max. | 4 A | |
| Cable length | ||
| ● shielded, max. | 500 m | |
| ● unshielded, max. | 500 m | |
| Interrupts/diagnostics/status information | ||
| Diagnostic functions | Yes | |
| Diagnostic messages | ||
| ● Wire-break | Yes | |
| ● Short-circuit | Yes | |
| Diagnostics indication LED | ||
| ● Group error SF (red) | Yes | |
| ● Status indicator digital output (green) | Yes | |
| Potential separation | ||
| Potential separation digital outputs | ||
| ● between the channels | No | |
| ● between the channels and backplane bus | Yes | |
| ● Between the channels and load voltage L+ | No | |
| Isolation | ||
| tested with | ||
| ● Load voltage L+ against backplane bus | 2 545 V DC | |
| Standards, approvals, certificates | ||
| Highest safety class achievable in safety mode | ||
| ● acc. to EN 954 | 4 | |
| ● Performance level according to ISO 13849-1 | PLe | |
| ● SIL acc. to IEC 61508 | SIL 3 | |
| Ambient conditions | ||
| Ambient temperature during operation | ||
| ● min. | -25 °C | |
| ● max. | 60 °C | |
| Extended ambient conditions | ||
| ● relative to ambient temperature-atmospheric pressure-installation altitude | Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) | |
| ● At cold restart, min. | -25 °C | |
| Relative humidity | ||
| — With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) | |
| Resistance | ||
| — against biologically active substances / conformity with EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against chemically active substances / conformity with EN 60721-3-3 | Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against mechanically active substances / conformity with EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
| Dimensions | ||
| Width | 30 mm | |
| Height | 81 mm | |
| Depth | 52 mm | |
| Weights | ||
| Weight, approx. | 85 g | |
| last modified: | 02/01/2017 | |
