Technická data
Název:
SIPLUS DP 4DI ET200S
Popis:
SIPLUS ET200S 4DI (1PU=5PCS) -25...+60 DGR C WITH CONFORMAL COATING BASED ON 6ES7131-4BD01-0AA0 . ELECTRONIC MODULE 24V DC WIDTH: 15 MM 5 PCS PER PACKAGING UNIT
Technické informace:
| Supply voltage | ||
| Rated value (DC) | ||
| ● 24 V DC | Yes; From power module | |
| permissible range, lower limit (DC) | 20.4 V | |
| permissible range, upper limit (DC) | 28.8 V | |
| Reverse polarity protection | Yes | |
| Input current | ||
| from supply voltage L+, max. | Dependent on encoder | |
| from backplane bus 3.3 V DC, max. | 10 mA | |
| Encoder supply | ||
| Type of output voltage | min. L+ (-0.5 V), under load | |
| Output current | ||
| ● Rated value | 500 mA | |
| ● permissible range | 0 to 500 mA | |
| Power loss | ||
| Power loss, typ. | 0.7 W | |
| Address area | ||
| Address space per module | ||
| ● with packing | 4 bit | |
| ● without packing | 1 byte | |
| Digital inputs | ||
| Number of digital inputs | 4 | |
| Input characteristic curve in accordance with IEC 61131, type 1 | Yes | |
| Input voltage | ||
| ● Type of input voltage | DC | |
| ● Rated value (DC) | 24 V | |
| ● for signal "0" | -30 to +5V | |
| ● for signal "1" | +15 to +30V | |
| Input current | ||
| ● for signal "1", typ. | 7 mA; at 24 V | |
| Input delay (for rated value of input voltage) | ||
| for standard inputs | ||
| — parameterizable | No | |
| — at "0" to "1", min. | 2 ms; typically 3 ms | |
| — at "0" to "1", max. | 4.5 ms | |
| — at "1" to "0", min. | 2 ms; typically 3 ms | |
| — at "1" to "0", max. | 4.5 ms | |
| Cable length | ||
| ● shielded, max. | 1 000 m | |
| ● unshielded, max. | 600 m | |
| Encoder | ||
| Connectable encoders | ||
| ● 2-wire sensor | Yes | |
| — permissible quiescent current (2-wire sensor), max. | 1.5 mA | |
| Interrupts/diagnostics/status information | ||
| Diagnostic functions | No | |
| Diagnostics indication LED | ||
| ● Group error SF (red) | No | |
| ● Status indicator digital input (green) | Yes; per channel | |
| Parameter | ||
| Remark | 1 byte | |
| Potential separation | ||
| Potential separation digital inputs | ||
| ● between the channels | No | |
| ● between the channels and backplane bus | Yes | |
| Permissible potential difference | ||
| between different circuits | 75 V DC/60 V AC | |
| Isolation | ||
| Isolation tested with | 500 V DC | |
| Standards, approvals, certificates | ||
| CE mark | Yes | |
| Ambient conditions | ||
| Ambient temperature during operation | ||
| ● min. | -25 °C; = Tmin | |
| ● max. | 60 °C; = Tmax | |
| Extended ambient conditions | ||
| ● relative to ambient temperature-atmospheric pressure-installation altitude | Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m) | |
| Relative humidity | ||
| — With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions) | |
| Resistance | ||
| — against biologically active substances / conformity with EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against chemically active substances / conformity with EN 60721-3-3 | Yes; Class 3C4 incl. salt spray. The supplied connector covers must remain on the unused interfaces during operation! | |
| — against mechanically active substances / conformity with EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
| Dimensions | ||
| Width | 15 mm | |
| Height | 81 mm | |
| Depth | 52 mm | |
| Weights | ||
| Weight, approx. | 35 g | |
| last modified: | 02/01/2017 | |
