Technická data
Název:
SIPLUS ET200S EM 2AO U
Popis:
SIPLUS ET200S EM 2AO U -25 ... +60 DEGREE C BASED ON 6ES7135-4FB01-0AB0
Technické informace:
| Supply voltage | ||
| Load voltage L+ | ||
| ● Rated value (DC) | 24 V; From power module | |
| ● Reverse polarity protection | Yes | |
| Input current | ||
| from load voltage L+ (without load), max. | 130 mA | |
| from backplane bus 3.3 V DC, max. | 10 mA | |
| Power loss | ||
| Power loss, max. | 2 W | |
| Address area | ||
| Address space per module | ||
| ● Address space per module, max. | 4 byte | |
| Analog outputs | ||
| Number of analog outputs | 2 | |
| Voltage output, short-circuit protection | Yes | |
| Voltage output, short-circuit current, max. | 25 mA | |
| Cycle time (all channels) max. | 1.5 ms | |
| Output ranges, voltage | ||
| ● 1 V to 5 V | Yes | |
| ● -10 V to +10 V | Yes | |
| Connection of actuators | ||
| ● for voltage output two-wire connection | Yes; Without compensation of the line resistances | |
| ● for voltage output four-wire connection | Yes | |
| Load impedance (in rated range of output) | ||
| ● with voltage outputs, min. | 1 kΩ | |
| ● with voltage outputs, capacitive load, max. | 1 µF | |
| Destruction limits against externally applied voltages and currents | ||
| ● Voltages at the outputs towards MANA | 15 V; max. 15 V continuous; 75 V for max. 1 s (mark to space ratio 1:20) | |
| ● Current, max. | 50 mA; DC | |
| Cable length | ||
| ● shielded, max. | 200 m | |
| Analog value generation for the outputs | ||
| Integration and conversion time/resolution per channel | ||
| ● Resolution with overrange (bit including sign), max. | 14 bit; 1 to 5 V: 12 bits, +/-10 V: 13 bits + sign | |
| Settling time | ||
| ● for resistive load | 0.1 ms | |
| ● for capacitive load | 0.5 ms | |
| ● for inductive load | 0.5 ms | |
| Errors/accuracies | ||
| Output ripple (relative to output range, bandwidth 0 to 50 kHz), (+/-) | 0.02 % | |
| Linearity error (relative to output range), (+/-) | 0.02 % | |
| Temperature error (relative to output range), (+/-) | 0.01 %/K | |
| Repeat accuracy in steady state at 25 °C (relative to output range), (+/-) | 0.05 % | |
| Operational error limit in overall temperature range | ||
| ● Voltage, relative to output range, (+/-) | 0.4 % | |
| Basic error limit (operational limit at 25 °C) | ||
| ● Voltage, relative to output range, (+/-) | 0.2 % | |
| Interrupts/diagnostics/status information | ||
| Substitute values connectable | Yes; 0 to 65535 (range of values must be within the rated range) | |
| Diagnostic messages | ||
| ● Short-circuit | Yes | |
| ● Group error | Yes | |
| Diagnostics indication LED | ||
| ● Group error SF (red) | Yes | |
| Parameter | ||
| Remark | 7 byte | |
| Diagnostics short-circuit | Disable / enable | |
| Output type/range | deactivated / 1 to 5 V / +/ -10 V | |
| Group diagnostics | Disable / enable | |
| Response to CPU/master STOP | Output current and de-energized/substitute a value/keep last value | |
| Potential separation | ||
| Potential separation analog outputs | ||
| ● between the channels | No | |
| ● between the channels and backplane bus | Yes | |
| ● Between the channels and load voltage L+ | Yes | |
| Permissible potential difference | ||
| between MANA and M internally (UISO) | 75 V DC/60 V AC | |
| Ambient conditions | ||
| Ambient temperature during operation | ||
| ● min. | -25 °C; = Tmin | |
| ● max. | 60 °C; = Tmax | |
| Extended ambient conditions | ||
| ● relative to ambient temperature-atmospheric pressure-installation altitude | Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m) | |
| Relative humidity | ||
| — With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) | |
| Resistance | ||
| — against biologically active substances / conformity with EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against chemically active substances / conformity with EN 60721-3-3 | Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against mechanically active substances / conformity with EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
| Dimensions | ||
| Width | 15 mm | |
| Height | 81 mm | |
| Depth | 52 mm | |
| Weights | ||
| Weight, approx. | 40 g | |
| last modified: | 02/01/2017 | |
