Technická data
Název:
SIPLUS_ET200S_4DO DC24V/2A
Popis:
SIPLUS ET200S EM 4DO DC24V/2A -25 ... +60 DEGREES C WITH CONFORMAL COATING BASED ON 6ES7132-4BD32-0AA0 5 PIECES PER PACKAGING UNIT
Technické informace:
| Supply voltage | ||
| Reverse voltage protection | Yes; when using the same load voltage as on the power module | |
| Load voltage L+ | ||
| ● Rated value (DC) | 24 V; From power module | |
| ● Reverse polarity protection | Yes | |
| Input current | ||
| from load voltage L+ (without load), max. | 10 mA; Per channel | |
| from backplane bus 3.3 V DC, max. | 10 mA | |
| Power loss | ||
| Power loss, typ. | 1.6 W | |
| Address area | ||
| Address space per module | ||
| ● with packing | 4 bit | |
| ● without packing | 1 byte | |
| Digital outputs | ||
| Number of digital outputs | 4 | |
| Short-circuit protection | Yes | |
| ● Response threshold, typ. | 2.8 to 7.2 A | |
| Limitation of inductive shutdown voltage to | Typ. L+ (-55 to -60 V) | |
| Controlling a digital input | Yes | |
| Switching capacity of the outputs | ||
| ● on lamp load, max. | 10 W | |
| Load resistance range | ||
| ● lower limit | 12 Ω | |
| ● upper limit | 3 400 Ω | |
| Output voltage | ||
| ● for signal "1", min. | L+ (-1.0 V) | |
| Output current | ||
| ● for signal "1" rated value | 2 A | |
| ● for signal "1" permissible range, min. | 7 mA | |
| ● for signal "1" permissible range, max. | 2.4 A | |
| ● for signal "0" residual current, max. | 0.5 mA | |
| Output delay with resistive load | ||
| ● "0" to "1", max. | 50 µs; Typ. 45 µs | |
| ● "1" to "0", max. | 120 µs; Typ. 90 µs | |
| Parallel switching of two outputs | ||
| ● for uprating | No | |
| ● for redundant control of a load | Yes; per module | |
| Switching frequency | ||
| ● with resistive load, max. | 1 000 Hz | |
| ● with inductive load, max. | 2 Hz; At 0.5 H | |
| ● on lamp load, max. | 10 Hz | |
| Total current of the outputs | ||
| ● Current per module, max. | 4 A | |
| Cable length | ||
| ● shielded, max. | 1 000 m | |
| ● unshielded, max. | 600 m | |
| Isochronous mode | ||
| Isochronous operation (application synchronized up to terminal) | Yes | |
| Interrupts/diagnostics/status information | ||
| Diagnostic functions | No | |
| Diagnostics indication LED | ||
| ● Status indicator digital output (green) | Yes | |
| Parameter | ||
| Remark | 1 byte | |
| Potential separation | ||
| Potential separation digital outputs | ||
| ● between the channels | No | |
| ● between the channels and backplane bus | Yes | |
| Isolation | ||
| Isolation tested with | 500 V DC | |
| Ambient conditions | ||
| Ambient temperature during operation | ||
| ● min. | -25 °C; = Tmin | |
| ● max. | 60 °C; = Tmax | |
| Extended ambient conditions | ||
| ● relative to ambient temperature-atmospheric pressure-installation altitude | Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m) | |
| Relative humidity | ||
| — With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) | |
| Resistance | ||
| — against biologically active substances / conformity with EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against chemically active substances / conformity with EN 60721-3-3 | Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against mechanically active substances / conformity with EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
| Dimensions | ||
| Width | 15 mm | |
| Height | 81 mm | |
| Depth | 52 mm | |
| Weights | ||
| Weight, approx. | 40 g | |
| last modified: | 02/01/2017 | |
