Technická data
Název:
SIPLUS ET200M IM153-2 EN50155
Popis:
SIPLUS ET 200M IM153-2 (*BA02) T1 RAIL -25 ... +60 Degree C T1 with 70 Degree C for 10 min with Conformal Coating BasedOn: 6ES7153-2BA10-0XB0 . Interface ET 200M IM 153-2 high feature for max. 12 S7-300 Modules, with redundancy, time stamping fit for Isochrone Mode New Features: 12 Modules / Station slave initiative for switches and drive ES; Extended Data for hart secondary variables Operaton with 64PT Modules extendes timestamps with 32 Signals / Slot
Technické informace:
General information | ||
Vendor identification (VendorID) | 801Eh | |
Supply voltage | ||
Rated value (DC) | ||
● 24 V DC | Yes | |
permissible range, lower limit (DC) | 20.4 V | |
permissible range, upper limit (DC) | 28.8 V | |
permissible range (ripple included), lower limit (DC) | 20.4 V | |
permissible range (ripple included), upper limit (DC) | 28.8 V | |
external protection for power supply lines (recommendation) | 2,5 A | |
Mains buffering | ||
● Mains/voltage failure stored energy time | 5 ms | |
Input current | ||
Current consumption, max. | 650 mA; with 24 V DC supply | |
Inrush current, typ. | 3 A | |
I²t | 0.1 A²·s | |
Output current | ||
for backplane bus (5 V DC), max. | 1.5 A | |
Power loss | ||
Power loss, typ. | 5.5 W | |
Address area | ||
Addressing volume | ||
● Inputs | 244 byte | |
● Outputs | 244 byte | |
Hardware configuration | ||
Number of modules per DP slave interface, max. | 12 | |
Time stamping | ||
Accuracy | 1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules | |
Number of message buffers | 15 | |
Messages per message buffer | 20 | |
Number of stampable digital inputs, max. | 128; Max. 128 signals/station; max. 32 signals/slot | |
Time format | RFC 1119 | |
Time resolution | 0.466 ns | |
Time interval for transmitting the message buffer if a message is present | 1 000 ms | |
Time stamp on signal change | rising / falling edge as signal entering or exiting | |
Interfaces | ||
Interface physics, RS 485 | Yes | |
Interface physics, FOC | No | |
PROFIBUS DP | ||
● Node addresses | 1 to 125 permitted | |
● automatic detection of transmission rate | Yes | |
● Output current, max. | 70 mA | |
● Transmission rate, max. | 12 Mbit/s | |
● Transmission procedure | RS 485 | |
● SYNC capability | Yes | |
● FREEZE capability | Yes | |
● Direct data exchange (slave-to-slave communication) | Yes; as publisher with all IO, as subscriber with F-IO only | |
● Connector type | 9-pin sub D | |
1. Interface | ||
DP slave | ||
● GSD file | SI05801E.GSG | |
● automatic baud rate search | Yes | |
Protocols | ||
Bus protocol/transmission protocol | PROFIBUS DP to EN 50170 | |
Isolation | ||
Isolation tested with | Isolation voltage 500 V | |
Degree and class of protection | ||
Degree of protection acc. to EN 60529 | ||
● IP20 | Yes | |
Standards, approvals, certificates | ||
CE mark | Yes | |
Railway application | ||
● EN 50155 | Yes; T1 Category 1 Class A/B horizontal mounting position | |
Ambient conditions | ||
Ambient temperature during operation | ||
● min. | -25 °C; = Tmin | |
● max. | 60 °C; = Tmax; the rated temperature range of -25 ... +55 °C (T1) applies for the use on railway vehicles according to EN50155 | |
Ambient temperature during storage/transportation | ||
● min. | -40 °C | |
● max. | 70 °C | |
Extended ambient conditions | ||
● relative to ambient temperature-atmospheric pressure-installation altitude | Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m) | |
● At cold restart, min. | -25 °C | |
Relative humidity | ||
— With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) | |
Resistance | ||
— against biologically active substances / conformity with EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation! | |
— against chemically active substances / conformity with EN 60721-3-3 | Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! | |
— against mechanically active substances / conformity with EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
Configuration | ||
Configuration software | ||
● STEP 7 | Yes; STEP 7 / COM PROFIBUS / non-Siemens tools via GSD file | |
Dimensions | ||
Width | 40 mm | |
Height | 125 mm | |
Depth | 117 mm | |
Weights | ||
Weight, approx. | 360 g | |
last modified: | 02/01/2017 |