Technická data
Název:
SIPLUS ET 200MP IM155-5 DP ST
Popis:
SIPLUS ET 200MP -25 ... +60 DEGREE WITH CONFORMAL COATING BASEDON 6ES7155-5BA00-0AB0 . PROFIBUS INTERFACE MODULE IM 155-5 DP ST FOR MAX. 12 S7-1500 MODULES
Technické informace:
| General information | ||
| HW functional status | 01 | |
| Firmware version | V2.0.0 | |
| Vendor identification (VendorID) | 81AAh | |
| Product function | ||
| ● I&M data | Yes; I&M0 to I&M3 | |
| Engineering with | ||
| ● STEP 7 TIA Portal configurable/integrated as of version | V13 / V13 | |
| ● STEP 7 configurable/integrated as of version | V5.5 SP3 / - | |
| ● PROFIBUS as of GSD version/GSD revision | V1.0 / V5.1 | |
| Supply voltage | ||
| Type of supply voltage | DC | |
| Rated value (DC) | 24 V | |
| permissible range, lower limit (DC) | 20.4 V | |
| permissible range, upper limit (DC) | 28.8 V | |
| Reverse polarity protection | Yes | |
| Mains buffering | ||
| ● Mains/voltage failure stored energy time | 5 ms | |
| Input current | ||
| Current consumption (rated value) | 0.2 A; at 24 V DC and without load | |
| Current consumption, max. | 1.2 A; at 20.4 V DC and max. load | |
| Inrush current, max. | 4 A | |
| I²t | 0.09 A²·s | |
| from interface 5 V DC, max. | 80 mA | |
| Power | ||
| Infeed power to the backplane bus | 14 W | |
| Power loss | ||
| Power loss, typ. | 4 W; Typical | |
| Address area | ||
| Address space per module | ||
| ● Address space per module, max. | 128 byte; per input / output | |
| Address space per station | ||
| ● Address space per station, max. | 244 byte; per input / output | |
| Hardware configuration | ||
| System power supply can be plugged in to left of IM | No | |
| Number of permissible power segments | 1 | |
| Rack | ||
| ● Modules per rack, max. | 12; I/O modules | |
| Interfaces | ||
| Number of PROFIBUS interfaces | 1 | |
| 1. Interface | ||
| Functionality | ||
| ● PROFIBUS DP slave | Yes | |
| Interface types | ||
| RS 485 | ||
| ● Transmission rate, max. | 12 Mbit/s | |
| Protocols | ||
| PROFIBUS | ||
| Services | ||
| — SYNC capability | Yes | |
| — FREEZE capability | Yes | |
| — DPV1 | Yes | |
| Interrupts/diagnostics/status information | ||
| Status indicator | Yes | |
| Alarms | Yes | |
| Diagnostic functions | Yes | |
| Diagnostics indication LED | ||
| ● RUN LED | Yes; Green LED | |
| ● ERROR LED | Yes; Red LED | |
| ● MAINT LED | Yes; yellow LED | |
| Potential separation | ||
| between backplane bus and electronics | No | |
| between PROFIBUS DP and all other circuit components | Yes | |
| between supply and all other circuits | No | |
| Permissible potential difference | ||
| between different circuits | 75 V DC/60 V AC | |
| Isolation | ||
| Isolation tested with | 707 V DC (type test) | |
| Ambient conditions | ||
| Ambient temperature during operation | ||
| ● horizontal installation, min. | -40 °C; = Tmin; Startup @ -25 °C | |
| ● horizontal installation, max. | 60 °C; = Tmax | |
| Extended ambient conditions | ||
| ● relative to ambient temperature-atmospheric pressure-installation altitude | Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m) | |
| Relative humidity | ||
| — With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation | |
| Resistance | ||
| — against biologically active substances / conformity with EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against chemically active substances / conformity with EN 60721-3-3 | Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against mechanically active substances / conformity with EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
| Dimensions | ||
| Width | 35 mm | |
| Height | 147 mm | |
| Depth | 129 mm | |
| Weights | ||
| Weight, approx. | 360 g | |
| last modified: | 02/01/2017 | |
