Technická data
Název:
SIPLUS S7-1500 DQ 32X24VDC/0.5A HF
Popis:
SIPLUS S7-1500 DQ 32x24VDC/0.5A -40 ... +70 DEG C WITH CONFORMAL COATING BasedOn: 6ES7522-1BL01-0AB0 . 32 CHANNELS IN GROUPS OF 8, 4 A PER GROUP; SINGLE-CHANNEL DIAGNOSIS; SUBSTITUTE VALUE
Technické informace:
| General information | ||
| Product type designation | DQ 32x24VDC/0.5A HF | |
| Product function | ||
| ● I&M data | Yes; I&M0 to I&M3 | |
| Operating mode | ||
| ● DQ | Yes | |
| ● MSO | Yes | |
| Supply voltage | ||
| Rated value (DC) | 24 V | |
| permissible range, lower limit (DC) | 20.4 V | |
| permissible range, upper limit (DC) | 28.8 V | |
| Reverse polarity protection | Yes; through internal protection with 7 A per group | |
| Input current | ||
| Current consumption, max. | 60 mA | |
| Output voltage | ||
| Rated value (DC) | 24 V | |
| Power | ||
| Power available from the backplane bus | 1.1 W | |
| Power loss | ||
| Power loss, typ. | 3.5 W | |
| Digital outputs | ||
| Number of digital outputs | 32 | |
| Current-sourcing | Yes | |
| Short-circuit protection | Yes; Clocked electronically | |
| ● Response threshold, typ. | 1 A | |
| Limitation of inductive shutdown voltage to | L+ (-53 V) | |
| Controlling a digital input | Yes | |
| Switching capacity of the outputs | ||
| ● with resistive load, max. | 0.5 A | |
| ● on lamp load, max. | 5 W | |
| Load resistance range | ||
| ● lower limit | 48 Ω | |
| ● upper limit | 12 kΩ | |
| Output voltage | ||
| ● for signal "1", min. | L+ (-0.8 V) | |
| Output current | ||
| ● for signal "1" rated value | 0.5 A | |
| ● for signal "1" permissible range, max. | 0.5 A | |
| ● for signal "0" residual current, max. | 0.5 mA | |
| Output delay with resistive load | ||
| ● "0" to "1", max. | 100 µs | |
| ● "1" to "0", max. | 500 µs | |
| Parallel switching of two outputs | ||
| ● for logic links | Yes | |
| ● for uprating | No | |
| ● for redundant control of a load | Yes | |
| Switching frequency | ||
| ● with resistive load, max. | 100 Hz | |
| ● with inductive load, max. | 0.5 Hz; According to IEC 60947-5-1, DC-13 | |
| ● on lamp load, max. | 10 Hz | |
| Total current of the outputs | ||
| ● Current per channel, max. | 0.5 A; see additional description in the manual | |
| ● Current per group, max. | 4 A; see additional description in the manual | |
| ● Current per module, max. | 16 A; see additional description in the manual | |
| Cable length | ||
| ● shielded, max. | 1 000 m | |
| ● unshielded, max. | 600 m | |
| Isochronous mode | ||
| Isochronous operation (application synchronized up to terminal) | Yes | |
| Execution and activation time (TCO), min. | 70 µs | |
| Bus cycle time (TDP), min. | 250 µs | |
| Interrupts/diagnostics/status information | ||
| Diagnostics function | Yes | |
| Substitute values connectable | Yes | |
| Alarms | ||
| ● Diagnostic alarm | Yes | |
| Diagnostic messages | ||
| ● Monitoring the supply voltage | Yes | |
| ● Wire-break | Yes | |
| ● Short-circuit | Yes | |
| ● Group error | Yes | |
| Diagnostics indication LED | ||
| ● RUN LED | Yes; Green LED | |
| ● ERROR LED | Yes; Red LED | |
| ● Monitoring of the supply voltage (PWR-LED) | Yes; Green LED | |
| ● Channel status display | Yes; Green LED | |
| ● for channel diagnostics | Yes; Red LED | |
| ● for module diagnostics | Yes; Red LED | |
| Potential separation | ||
| Potential separation channels | ||
| ● between the channels | No | |
| ● between the channels, in groups of | 8 | |
| ● between the channels and backplane bus | Yes | |
| Isolation | ||
| Isolation tested with | 707 V DC (type test) | |
| Ambient conditions | ||
| Ambient temperature during operation | ||
| ● horizontal installation, min. | -40 °C; = Tmin | |
| ● horizontal installation, max. | 70 °C; = Tmax; see Derating BasedOn (e.g. manual), additionally Tmax > 60 °C max. aggregate current 2 A per group | |
| Extended ambient conditions | ||
| ● relative to ambient temperature-atmospheric pressure-installation altitude | Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m) | |
| Relative humidity | ||
| — With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation | |
| Resistance | ||
| — against biologically active substances / conformity with EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against chemically active substances / conformity with EN 60721-3-3 | Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! | |
| — against mechanically active substances / conformity with EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! | |
| Decentralized operation | ||
| Prioritized startup | Yes | |
| Dimensions | ||
| Width | 35 mm | |
| Height | 147 mm | |
| Depth | 129 mm | |
| Weights | ||
| Weight, approx. | 280 g | |
| last modified: | 02/01/2017 | |
